[. . . ] Multimedia Projector
MODEL
PDG-DWL100
Owner's Manual
Table of Contents
Table of Contents Usage Notice
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Introduction
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is recommended to use Eco under normal condition.
On: lower power consumption than Normal mode in Stand-by
condition.
Off: normal power consumption in Stand-by condition. Remote Control
This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. When operating the projector in "Code 2", both the projector and the remote control must be switched to "Code 2". To change the code for the projector: Select either "Code 1" or "Code 2" in this Setting Menu. To change the code for the remote control: Press and hold both the MENU and IMAGE buttons together for 10 seconds or more. After changing the code, make sure the remote control operates properly.
N ot e
After keystone adjustment, maybe need to re-adjust screen again during display the closed caption.
Closed Caption
This function is a printed version of the program sound or other information displayed on the screen. If the input signal contains closed captions, you can turn on the feature and switch the channels. Use the or to select Off, CC1, CC2.
Power Management
Set the interval of power-off of the system, if there is no signal input. (minutes/unit)
Sound
Mute:
Choose "On" to mute the volume. Choose "Off" to restore the volume.
28
English
User Controls
Volume:
Press the Press the to decrease the volume. to increase the volume.
Lamp Counter Reset
Reset the lamp life hour after replacing a new lamp.
Security Settings Security Settings:
On: Choose "On" to enable security verification when turning on the projector. Off: Choose "Off" to be able to switch on the projector without password verification.
Change Password:
First Time: 1. Use number buttons to enter default password and then press "ENTER" to confirm. Use number buttons on the remote to enter your new password and then press "ENTER" to confirm. (The password has to be 4 digits. )
N ot e
Password default value is "1234" (first time). If you input incorrect password 3 times, the projector will automatically shut itself down and enter into standby mode.
4. Use number buttons to enter current password and then press "ENTER" to confirm. Enter new password (4 digits in length) using the number buttons on the remote, then press "ENTER" to confirm. Enter new password again and press "ENTER" to confirm.
Factory Default
Return the adjustments and settings to the factory default values. (except for lamp counter and security setting)
English English
29
User Controls
Setting/Network
Network Status
Display the network connection status.
DHCP
Display the network connection status.
On: Assign an IP address to the projector from the DHCP server
automatically.
Off: Assign an IP address manually. IP Address
Select an IP address.
Subnet Mask
Select subnet mask number.
Gateway
Select the default gateway of the network connected to the projector.
DNS
Select DNS number.
Apply
Press "ENTER" button to apply the selection.
30
English
User Controls
Language
Language
N ot e
In the first instance of powering on the projector, the language menu is displayed to select the default language. [. . . ] Please, dispose of them correctly at your local community waste collection/recycling centre. Please, help us to conserve the environment we live in!
English English
55
Appendices
Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port.
1. Connect a RS-232C serial cross cable to SERVICE PORT on the projector and serial port on the PC. Launch a communication software provided with PC and setup the communication condition as follows: 3. [. . . ]